Our services

Eight services, each scoped to the property in front of us.

Brass fittings and braided flexible hoses on a dark slate surface

General Plumbing

Supply and waste systems, fixtures and fault-finding for houses and business premises.

General plumbing covers the everyday systems that a building depends on: cold and hot water supplies, waste and vent pipework, and the fixtures connected to them.

Work is scoped to the property and the system in front of us: isolating the affected section, renewing failed components and testing the repair before the area is left clean.

Typical work

  • Isolation valves, stopcocks and filled loops
  • Replacement of taps, traps, waste fittings and connectors
  • Leak diagnosis and targeted repair of pipe runs
  • Testing of repaired sections and recommissioning
First-fix pipework routed and capped inside a stripped-back timber frame

Plumbing Installation

First-fix and second-fix installation of complete plumbing systems in new builds and renovations.

Installation starts from the point of origin: the incoming water main, the cold water storage and the route the supply takes through the building.

Pipework is set out, fixed and pressure tested before fixtures are fitted, so the system is proven before it is dressed or tiled.

Typical work

  • First-fix routing, fixing and capping of pipework
  • Installation of basins, baths, WCs and shower valves
  • Connection of appliances and sanitary ware
  • Pressure testing, flushing and commissioning
Supply and waste pipework beneath a kitchen sink with the cupboard doors open

Plumbing Repairs

Diagnosis and repair of leaks, blockages, dripping fittings and damaged pipework.

Repairs begin with a proper diagnosis rather than a guess. The system is traced, the fault is located and the smallest effective intervention is agreed before work starts.

Where a section of pipework has failed, the damaged length is replaced and the run is tested to confirm it holds.

Typical work

  • Trace and leak detection on concealed pipework
  • Clearing of blocked waste and overflow routes
  • Replacement of failed joints, valves and flexible connectors
  • Making good and tidying of the working area
Black external waste pipe with a bend running down a brick wall

Drainage Solutions

Above-ground and underground drainage, soil stacks, inspection chambers and maintenance.

Drainage is planned as a gravity system: falls, vents and joints are set out so that waste leaves the building predictably and vents stay balanced.

Both internal soil stacks and external drainage runs are covered, including the inspection points that allow a system to be maintained without opening ground.

Typical work

  • Soil stacks, vents and branch connections
  • Inspection chambers and rodding access
  • Repairs to underground and above-ground drainage
  • Cesspit and interceptor maintenance coordination
A wall-mounted boiler above a manifold of heating pipework

Water Heating

Water heating systems, cylinders, controls and the pipework that serves them.

Heating installations are matched to the property: the emitters, the pipework and the hot water arrangement are considered together rather than in isolation.

Systems are commissioned on completion, with controls, circulation and safety devices set and checked as part of the handover.

Typical work

  • Installation and replacement of cylinders and heat sources
  • Radiator and underfloor heating connections
  • Controls, pumps and circulation set-up
  • Commissioning and temperature balancing
Copper pipework and brass valves on a manifold fixed to a wall

Pipework & Upgrades

Renewal, rerouting and upgrading of existing pipework, pressure and incoming supply.

Older pipework is frequently replaced rather than repaired. Upgrades cover material changes, rerouting around new construction, and improving pressure and flow at the point of use.

Pipework is fixed to a planned route with correct brackets and spacing, so it stays serviceable long after the job is finished.

Typical work

  • Replacement of old, corroded pipe runs
  • Rerouting around structural changes and new layouts
  • Pressure improvement, pump and storage upgrades
  • Manifolds, valves and isolation strategy
A walk-in shower with a rain head, handset and glass screen in a tiled room

Bathroom Plumbing

Bathrooms fitted out end to end: baths, basins, showers, WCs and concealed systems.

A bathroom is a single plumbing problem with many parts. The supply, the waste, the ventilation and the fixtures are planned together so the finished room works as one system.

Where cisterns or valves are concealed, the frame and duct are installed to the point where the tiles can be closed up around it.

Typical work

  • Baths, basins, WCs and shower installations
  • Concealed cisterns, frames and ducting panels
  • Wet rooms, tiling preparation and tanking
  • Ventilation and extraction provisions
Plant room pipework with pumps, valves and pressurisation vessels

Commercial Plumbing

Plumbing, washroom and plant room works for commercial premises and shared buildings.

Commercial work is scheduled around how a building is used. Preparation areas, washrooms and plant rooms are planned so trades can work in sequence without closing the space.

Systems are specified for throughput and maintenance access, with isolation points placed where they can actually be reached.

Typical work

  • Commercial kitchen and washroom installations
  • Plant room, boiler room and riser pipework
  • Shared and multi-occupancy service upgrades
  • Maintenance routines and fault response planning